Payment & Shipping Terms:
|Temp. Range:||-70℃～+150℃||Temp. Deviation:||≤±2.0℃|
|Temp. Fluctuation:||±0.5℃||Humidity Range:||30%R.H.～95%R.H|
|Workplace Volume:||W 1200 × H 2300 × D 1500 Mm||Exterior Size:||W 1500 × H 2700 × D 3530 Mm|
|Cable Port:||φ100mm*1 Located On Both Side Of Chamber, With Rubber Stopper||Test Per:||IEC And UL Requirements|
0.5℃ Environmental Test Chamber,
95%R.H Environmental Test Chamber,
IEC 61215 climatic test chamber
KOMEG Specialized Environmental Test Chambers for Solar Panel Testing (Walk-in Type)
Specialized Chambers for Solar Panel Tests
KOMEG offers a wide variety of test chambers that allow you to test per the IEC and UL requirements. We can work with you to decide which equipment has the needed size and features to suit your application.
such as desired throughput, testing methodology, floorspace, and budget will affect the final selection.
Our chambers can be used for the following test methods:
•10.11 Thermal Cycle Test
Requires temperature cycling between 85°C and -40°C,
50 or 200 times.
•10.12 Humidity Freeze Test
Cycling between hot/humid 85°C/85%RH and subfreezing -40°C ten times, with extended soaks at 85/85.
•10.13 Damp Heat Test
A long term, 1,000 hours, test at 85°C/85%.
Selecting a Chamber
Because the change rates in the specifications are
flexible, you have a choice of selecting a slower system to save cost and utilities, or a faster system to shorten testing time.
In order for KOMEG to select the proper heating/cooling subsystems, we will need to know:
• Chamber interior space required
• Total mass of modules and supporting racks to be tested
•Desired heat & cooling rates (Otherwise KOMEG will quote systems to meet both minimum or maximum rates allowed by IEC.)
Lengthy IEC and UL Tests
All three of the IEC 61215 & 61646 environmental tests KOMEG chambers are used for can be done in the same test chamber. It may be better, however, to consider multiple chambers to save time and electricity due to the lengths of the tests:
•The temperature cycling test may last up to seven weeks.
•The damp heat test is six weeks long.
•The damp heat test requires only minimal refrigeration, reducing capital and energy costs if a dedicated model is selected for this test
Standards Implemented and met
GB-2423.1-2008(IEC68-2-1)Test A: Cold Test
GB-2423.2-2008(IEC68-2-2)Test B: Dry Heat Test
GJB360.8-2009(MIL-STD.202F) Heat Aging Test
GJBl50.3-2009 (MIL-STD-810D) high temperature test method.
GJBl50.4-2009 (MIL-STD-810D) low temperature test method.
GB2423.3-2008 (IEC68-2-3) Test Ca: Constant damp heat test method.
GB2423.4-2008 (IEC68-2-30) Test Db: Alternating damp heat test method.
GJBl50.9-2009(MIL-STD-810D) Damp heat test chamber technical conditions
The machine complies with IEC61215 10.11, 10.12, 10.13 items IEC61215 10.11 test conditions:
|Water-cooled. The specifications measurement in the environment temperature at + 25 ℃ without load|
|1.1 Temp. range||-70℃～+150℃|
|1.2 Temp. deviation||≤±2.0℃|
|1.3 Temp. fluctuation||±0.5℃|
|1.4 Heating up rate||From -40℃ to +85℃, linear, ≧200℃/h, with a load of 300kg, No Heat Emission|
|1.5 Cooling rate||From -40℃ to +85℃, linear, ≧200℃/h, with a load of 300kg, No Heat Emission|
|2.1 Humidity range||30%R.H.～95%R.H|
|2.2 Humidity range|
|2.3 Humidity deviation||±3.0％RH(＞75％RH)±5.0％RH(≤75％RH)|
|2.4 Humidity fluctuation||±2.0％RH|
|3. Floor capacity||300KG/m2|
|4. Full load||
10 PV Modules to be loaded in a vertical orientation.
Single panel max. size of 2000*1000*50mm.
Total weight of 300KG.
Temperature and humidity performance test are in accordance with the relevant provisions of the IEC60068 -3 standard
measurement; sensor placed in the unit outlet. According to national test standard: GB/T 5170.2, use 9 test point
calibration, as below:
|The overall structure and chamber are composed of three parts as below. Insulation box, separate refrigeration units, and electrical control cabinet.|
|1. Body dimensions||Workplace volume: W 1200 × H 2300 × D 1500 mm, Exterior size: W 1500 × H 2700 × D 3530 mm,|
|2. Insulation Box||
※ wall material: high-quality carbon steel※ inner wall material: SUS304 # matte stainless steel plate※
100mm rigid polyurethane foam insulation layer + glass fiber.
|3. Door||Double door (according to design), with observation window (the size depend on final design)|
|4. Lighting Device||Moisture-proof lighting, with explosion-proof lampshades.|
|5. Cable port||φ100mm*1 located on both side of the chamber, with a rubber stopper|
|6.Electric control box||Total power circuit breaker, over-temperature protection.|
|7. Control model||
This device is Cascade compression refrigeration
We use intellectual cooling control: PID will control solenoid-valve and heater on/off to adjust cooling or heating capacity according to temperature and loading requirements and status inside the chamber. Only cooling or only heating will be activated to get temperature balance to save energy
|8. Heating||High quality nickel-chromium alloy wire electric heaters, Non-contact control mode(SSR)|
|9. Water outlet hole||Available for drain the condensate water|
|10. Water purifier||Pure water device, 1 pcs, please provide 1 ~ 2 kg/cm2 tap water|
|11. Water supply system||Pump to enhance automatic water supply|
|12. Humidification||Stainless steel corrosion-resistant electric evaporative humidification|
|13. Humidity sensor||High accuracy Vaisala electronic humidity sensor|
Contact Person: Bella Mo