Payment & Shipping Terms:
|Controller:||Touch Screen Programmable Controller||Item:||Rapid-Rate Thermal Cycle Chamber|
|Warranty:||12 Months On Parts (excluding The Damages Caused By The Natural Disasters, Abnormal Power, Improper Operation And Maintenance, Etc)||Cooling Mode:||AIR Cooled|
|Temp Rate Of Change( ℃/Min):||5||Working Chamber Volume(L):||1000|
|Performance:||-70℃～+100℃||Power:||AC 380V/50Hz 3phase 5 Wires+ Ground Wire|
Thermal Cycle Chamber,
temperature cycling chamber
KOMEG ESS Models Large-capacity Rapid-Rate Thermal Cycle Chamber
The ESS models are the ideal temperature and humidity chambers for environmental testing of automotive parts for which test demands are becoming stricter.
It is available from a 150-liter or 1000-liter capacity, a temperature rate of change of 5°C, 10°C or 15°C per minute, and whether or not to have humidity control.
Not only do these models feature a high temperature rate of change performance, but by adding an added boiler humidifier, the humidity change time can be shortened and dew condensation test standards for automotive parts can be supported.
These models use the same touch panel instrumentation adopting Platinous flagship series for improving operability.
Wind simulation allows achieving minimum temperature variations of the specimen, for accurate and quick temperature changes. Specimen temperature ramp rate is 15°C/min.
Greater temperature ramp control
High precision of the specimen temperature control achieved thanks to a sensor for temperature specimen measurement, and the embedded high-speed controller.
refrigeration capacities increased at low temperatures,
minimization of the difference between test area and specimen temperatures,
airflow speed uniformity,
lead to excellent temperature ramp control.
A specimen temperature control mode meeting ramp rate conditions of JEDEC standard (15°C/min.)
Cable ports are equipped on both left and right side, to ease specimen access and wiring.
Overall structure, new test chamber designed very easy to operation and maintenance:
Water and electricity system separation design;
External humidifying design;
Three levels of overheat protection, easy access for refrigeration servicing, etc.
machines for sheet metal processing;
Tecumseh, Bock Compressor;
High quality electronic components (e.g. DANFOSS, ALCO, RANCO, SPORLAN, SAGINOMIYA, Schneider solenoid valve)
Standards Implemented and Met
GB10592-89 Technical requirements for high and low temperature test chamber
GB2423.1-1989 Low temperature test
GB2423.2-1989 High temperature test mode
Full System Level Testing
|Working Chamber Volume(L)||225||408||1000|
|Temp Rate of Change( ℃/Min)||5||10||5||10||5||10|
|Rapid Temp Change -40℃～+85℃ Full Linear Control|
|Exterior Material||Cold-rolled steel sheet (Rust proof & Plastic Spray treated )/ Stainless Steel|
|Interior Material||Stainless Steel Plate(SUS 304)|
|Insulation Material||Rigid Polyurethane Foam|
|Safety Devices||over pressure,over heat and over current protection for compressor, over temp. protection,|
|Cooling Mode||Water Cooled|
|Control system||Balanced Temperature & Humidity Control System(BTC type)|
|Heater||Iron-chrome wire heater|
|Observation Window||Glass incorporating heat generator|
|Controller||Touch screen programmable controller|
|Power||AC 380V/50Hz 3phase 5 wires+ Ground wire|
Note: 1. We reserve the right to change specifications without prior notice
We use PP Film wrapping the test chamber to protect the test chamber from moisture or being scratched first, then use strong plywood case for easyload and transport, and to keep the chambers from potential crash or impact.
If you face any problems in future during testing process we promise we will give you a reply within 48 hours and solution provide within 3 working days. We can offer operation video and English operation muanual. We can provide video-conference. If customers require on-site service, the transport and travel expense shall be borne by customer.
1. Do you know KOMEG?
KOMEG Designed to Meet Internationally Accepted Climatic Test Chambers. As a professional manufacturer and the best brand climatic chamber in China, KOMEG specialized in Environmental testing equipment for quality conscious people since 1990. Our products are CE approved and we are the supplier for ,UL, and world top 500 companies.
|Model :||Mechanically cooled test chambers, Liquid nitrogen cooled test chambers, Modular Walk-in Chambers|
|Application||To test the effects of specified environmental conditions on industrial products, electronic devices and components, materials, and biological items|
|Warranty:||1 year as standard, longer time can be negotiable|
|Place of Origin:||China|
2. What we working for ?
Our customers are the most important people ever in KOMEG Company. Our customers are not dependent on us KOMEG; We KOMEG are dependent on them. Our customers are not an interruption of our work; there are the purposes of it. We are not doing our customers a favor by serving them, there are doing us a favor by giving us an opportunity to do so. Our customers are not an outsider to our business, there are parts of it. Our customers are not someone to argue with; nobody ever won an argument with a customer. Our customers are not people who bring us their wants; it is our job to fill them profitably to them and to ourselves.
Contact Person: Peter Zhang