Payment & Shipping Terms:
|Product Name:||Programmable Walk-in Test Chambers||Application:||Reliability Testing, Research & Development Testing, Failure Analysis|
|Volume(M3):||120CBM||Door Size:||Single Wing:W80*H180;Double Wing:W160*H180|
|Temp. Constancy:||+/-0.5oc||Humidity Constancy:||+/-2.5%R.H|
|H.S. Code:||90321000||Delivery:||60 Working Days|
|Installation:||Yes Based On Your Arrangement Of Room And Board|
walk in environmental chamber,
walk in humidity chamber
Customized Environmental Temperature Humidity Walk-In Chamber for Solar Panel Vehicle Testing
1. Environmental Walk-In Test Chambers Advantages:
APPLICATION FOR SOLAR PANELS
The IEC (International Electrotechnical Commission) established environmental testing methods for solar panels that include operation at 85°/85%, thus requiring solid construction chamber.
The size and number of solar panels being tested at one time benefis from full-opening doors and heavy-duty flor construction.
Because the conditioner is separated for shipment, these units can be more easily shipped to countries wheresolar panels are being manufactured.
Custom built chambers
Drive-in chambers are typically built using panelized construction, but can use solid construction if testing requirements demand it. KOMEG customizes each drive-in to include features to suit the client’s simulation requirements.
Additional testing conditions
Chassis dynamometer or four-post road simulator:
KOMEG builds special flor interfaces to allow use of these additional types of equipment supplied by other vendors.
KOMEG builds infrared systems to create radiant surface heating of vehicles to look for deformation and other quality problems. These systems can be adjusted vertically and angled to ensure even coverage.
From cold-start to high-heat stress, a running engine is a common need, but complicated requirement.
Fresh air must be conditioned and introduced to the chamber to make up for that used in combustion, and exhaust must be safely removed from the chamber.
Main Technical Parameters
|Interior Dimensions||W4000 x H5000 x D6000mm|
|Exterior Dimensions||Actually design|
|Safety Devices(standard)||No fuse breaker, over pressure, over heat and over current protection for compressor, over temperature protection, over load protection for blower, dry heat protection|
|Standard accessories||Sight window*1, cable port ( portΦ50mm ) *1, chamber lamp*1, status indicator|
|Control System||Balanced Temperature & Humidity Control System|
|Refrigeration system||Water Cooled|
|Semi-hermetic compressor, single stage or cascade refrigeration system,|
|CFC free refrigerant ( HFC-507 and HFC-23 )|
|Controller||Panel||7-inch LCD Touch panel, Chinese or English display selectable|
|Operation model||Program or fix point running|
|Memory capacity||120 programs,1200steps, all repeat 999 cycles,part repeat 99 cycles|
|Accuracy||Temp.:0.1% of F.S ± 1 digit Humidity:0.1% of F.S ± 1 digit|
|Input||Temp.: pt-100, Humidity: pt-100 or ～5V DCV|
|Comm.port||RS-232 or RS-485 ( Softawre is option)|
|Temp. range||Maximum: 80 ºC,120 ºC;
Minimum: -60 ºC, -50 ºC, -40 ºC, -30 ºC, -20 ºC, -10 ºC, 0 ºC
|Humidity Range||10%, 20%, 30% ~ 95%|
|Temp. constancy||±0.5 ºC|
|Temp. uniformity||±2.0 ºC|
|Ambient Temp.||+5 ºC～+35 ºC|
|Wiring method||AC 380 ± 10% 50Hz ,3 phase 4 wires + Ground Wires|
|Heat up time||+20 ºC～+80 ºC, Within 60 min|
|Pull down time||+20 ºC ~ -55 º, -40 ºC, -20 ºC, -10 ºC, Within 120 or 90 or 60 min|
|Interior material||Stainless Steel Plate(SUS 304)|
|Exterior material||Baked Painting Steel Or Stainless steel ( SUS304)|
|Insulation material||Rigid polyurethane foam|
|Door size (mm)||Single wing: W800 x H1800; Double wing: W1600 x H1800;|
|Note:1. We reserve the right to change specifications without prior notice 2.Customized sizes and configurations available|
Control method and characteristics:
Precision microcomputer control temperature and humidity system, with PID control the refrigerant flow to make the system’s heating / humidification reduction, to achieve low power consumption, energy saving, carbon reduction effect, cooling, heating, humidity control intelligent electronic control, long-term stable use.
Flexibility for structure
The panels used in our chamber are 4” (100mm or 150mm) Thick urethane-foam sandwiched between a stainless-steel interior wall and a coated-steel exterior. An assembled box is self-supporting. So that no heavy structural members are required. Different door sizes, flooring upgrades,access ports, and other modifications are possible.
Widest test range, most customizable
Contact Person: Peter Zhang